PLYWOOD/ CRESS PLYWOOD / PLY PANEL


Preparation ans application procedure

PLYWOOD
PREPARATION
Procedure:

  • Sand well to roughen the surface (with 40 grain sandpaper).
  • Clean with Texnov Surface Preparer.
  • Let the surface dry for 48 hours.
  • Caulk your joints with elastomeric polyurethane caulking (e.g.: Adbond 009, Sonneborn NP1 caulking or equivalent) taking care to caulk only the joints.
  • Let dry as per manufacturer’s instructions before applying the finish coating.
FINISH COATING
After preparing the surface…

 Procedure:

  • You can fill the screw heads with TexNov Acrylic Coating (screws should be rust proof: zinc, ceramic).
  • Apply 2 coats of TexNov Acrylic Coating. Use a brush or roller with 10 mm bristles (24 hours between applying each coat of sealant).
  • Let the surface dry for a 24-hour period before applying the sealant.

Note:

  • TexNov Acrylic Coating will not hide all defects due to an unevenly installed substrate.
SEALANT
After preparing the surface and applying the coating (if necessary) …

Procedure:

  • Apply 2 coats of Met-30 Sealant. Use a brush or roller with 10 mm bristles (24 hours between each coat).
  • Let the surface dry for 24 hours.

Note :

  • All wood surfaces located less than 60” from the ground or poorly ventilated should ideally be sealed on all sides with Met-30 Sealant. This will prevent premature deterioration of the wood due to the migration of moisture from the ground to the sky.

CRESS PLYWOOD/ PLY PANEL
PREPARATION
Procedure:

• Sand well to roughen the surface (with 40 grain sandpaper).

• Clean with Texnov Surface Preparer.

• Let the surface dry for 48 hours.

• Caulk your joints with elastomeric polyurethane caulking (e.g.: Adbond 009, Sonneborn NP1 caulking or equivalent) taking care to caulk only the joints.

• Let dry as per manufacturer’s instructions before applying the sealant.
SEALANT
After preparing the surface…

Procedure:

• Apply 2 coats of Met-30 Sealant avoiding that the resin and glue go through the coating and make surface rings. Use a brush or roller with 10 mm bristles (24 hours between each coat).

• Let the surface dry for 24 hours prior to applying the finish coating.
FINISH COATING
After preparing the surface and applying the sealant…

Procedure:

  • You can fill the screw heads with TexNov Acrylic Coating (screws should be rust proof: zinc, ceramic).
  • Apply 2 coats of TexNov Acrylic Coating. Use a brush or roller with 10 mm bristles (24 hours between applying each coat).
  • Let the surface dry for 24 hours before applying the sealant.

Note:

  • TexNov Acrylic Coating will not hide all defects due to an unevenly installed substrate.
SEALANT
After preparing the surface, applying the sealant and applying the coating…

Procedure:

  • Apply 2 coats of Met-30 Sealant. Use a brush or roller with 10 mm bristles (24 hours between each coat).
  • Let the surface dry for 24 hours.

Note:

  • All wood surfaces located less than 60” from the ground or poorly ventilated should ideally be sealed on all sides with Met-30 Sealant. This will prevent premature deterioration of the wood due to the migration of moisture from the ground to the sky.

MAINTENANCE :

Clean the surface with TexNov Surface Preparer (3 water / 1 Preparer). Let dry and add a coat of Met-30 Sealant every 3 years or as needed. This should enable you to keep your surface in good condition.