Pintura – pre-coloured matte finish paint

Table de matières

TexPro PINTURA – Pre-coloured matte finish paint #

1- Product description #

TexPro Pintura is a liquid coating based on resins 100% acrylic. The TexPro Pintura is available in all the 96 standard colors.

Features #

100% acrylic.

Applicable with roller and with an air gun.

Good covering power.

Vapor permeability.

Benefits #

Improves adhesion of finishes.

Easy to use.

Can be tinted to the desired desired color.

Let the walls breathe.

2- Use #

TexPro Pintura has been specially developed as a as a primer before the application of the finishing coat

(coordinate the color of the base coat with the color of the of the finishing coat). Designed for surfaces of concrete, masonry, gypsum board and stucco.

TexPro Pintura is also used to refresh surfaces acrylic, stucco or plaster. It also has the property to prevent efflorescence from appearing at the

surface of the finishes.

3- Covered area #

  • 3.78L container: 1 coat covers 160 ft2 (14.5 m2)
  • 7L container: 1 coat covers 280 ft2 (25 m2)
  • 18.9L container: 1 coat covers 800 ft2 (74 m2)

The level of porosity of the substrate and the temperature can affect the surface area covered by the product.

4- Mixing #

Stir until smooth and homogeneous. No additives or accelerants should be added.

Adding water is not recommended as it will increase the drying time. If the drying time is very short and the marks of the rolls are noted, you must add a maximum of maximum of 250 ml of water (1 cup = per 18.9L tank). 18,9L)

5- Installation #

TexPro Pintura should be applied away from direct sunlight and of the weather. Air and surface temperature must be 10°C (50°F) or higher and remain so for a minimum for a minimum of 24 hours.

Temporary protection: #

During the entire time of the plaster application and for 4 hours after 4 hours after application, the wall must be protected protected against bad weather and other possible possible damage.

Surface preparation: #

The surface to be covered must be clean, dry, of good quality quality, free of crust, grease, oil, etc.

Clean the surfaces to be coated with the products necessary. Remove blisters and flakes that formed on painted surfaces before applying TexPro Pintura.

TexPro Pintura can be applied with a brush roller or sprayer.

Drying: #

The drying time of TexPro Pintura depends on the air temperature and relative humidity. In normal conditions 30°C (86°F) and 75% R.H.

TexPro Pintura is dry to the touch after 1 hour and dry enough dry enough to apply a finishing coat after 2 hours.

Cleaning #

Clean tools with water while TexPro Pintura TexPro Pintura is still wet.

6- Storage of the product #

TexPro Pintura must be stored at a temperature of 5 to 40°C (41 to 104°F) in a well-sealed container. 40°C (41 to 104°F) in a well sealed container and not and not exposed to sunlight.

The lifetime of the of the product is 1 year.

7- Physical properties #

  • Solids 65.0
  • pH 9.5
  • Viscosity with Brookfield RVT model,
  • propeller no. D / 10 rpm 15000 cps
  • Density at 20°C 1.27 g/cm
    3
  • Glass transition temperature at midpoint / Tg + 14°C
  • V.O.C. (volatile organic compounds in g/L) 35

8- Transport conditions #

  • Regulatory Name: Not applicable.
  • TDG Classification: Not regulated.

Note: This product does not require any special measures for international transport